Removing & Replacing Parts | HP EliteBook x360 830 G8 Notebook PC | HP Computer Service | @HPSupport

Introduction

This tutorial provides a comprehensive guide on how to remove and replace various components of the HP EliteBook x360 830 G8 Notebook PC. Whether you're servicing your device or looking to upgrade it, following these detailed steps will ensure that the process is executed correctly, helping to maintain or enhance your laptop's performance.

Step 1: Remove the Base Enclosure

• Gather Tools: You will need a Phillips screwdriver and a plastic pry tool.
• Power Down the Device: Ensure the laptop is turned off and unplugged.
• Remove Screws: Unscrew the screws holding the base enclosure.
• Pry Open the Base: Use the plastic pry tool to gently lift the base enclosure from the notebook.

Step 2: Replace the Battery

• Locate the Battery: Once the base is removed, locate the battery.
• Disconnect the Battery: Carefully unplug the battery connector.
• Remove the Battery: Unscrew the battery and lift it out.
• Install the New Battery: Place the new battery in position, screw it back, and reconnect the battery connector.

Step 3: Upgrade the M.2 Solid State Drive

• Find the M.2 Slot: After removing the battery, locate the M.2 SSD slot.
• Unscrew the SSD: Remove the screw securing the SSD.
• Pull Out the Old SSD: Slide the SSD out of its slot.
• Insert the New SSD: Insert the new M.2 SSD at an angle and secure it with the screw.

Step 4: Replace the Wireless LAN Module

• Identify the Wireless LAN Module: Find it near the M.2 slot.
• Unscrew and Disconnect: Remove screws and unplug the antenna wires carefully.
• Remove the Module: Lift the module out of its slot.
• Install the New Module: Place the new wireless LAN module and reconnect the antenna wires.

Step 5: Replace the Wireless WAN Module

• Locate the Wireless WAN Module: It is typically next to the wireless LAN module.
• Follow Similar Steps as Above: Unscrew, disconnect, remove, and replace with a new WAN module.

Step 6: Change the DC-in Connector

• Access the Connector: It may be covered; remove any obstacles.
• Unscrew the Connector: Take out the screws holding it in place.
• Disconnect Wires: Carefully unplug the connector.
• Install the New Connector: Place the new connector in its position and reconnect it.

Step 7: Replace the NFC Module

• Find the NFC Module: This is usually located near the touchpad.
• Unscrew and Disconnect: Remove screws and unplug the module.
• Remove and Replace: Lift out the old module and insert the new one.

Step 8: Replace the RTC Battery

• Locate the RTC Battery: This is usually a coin-cell battery on the motherboard.
• Remove the Old Battery: Gently pry it out.
• Insert the New RTC Battery: Place the new battery in the same orientation.

Step 9: Change the Touchpad with NFC Antenna

• Unscrew the Touchpad: Remove screws securing the touchpad.
• Disconnect the Cable: Unplug the cable from the motherboard.
• Install the New Touchpad: Position the new touchpad and reconnect the cable.

Step 10: Replace the System Fan

• Locate the System Fan: It is usually near the heat sink.
• Unscrew and Disconnect: Remove screws and unplug the fan.
• Install the New Fan: Place the new fan and secure it with screws.

Step 11: Change the Heat Sink

• Remove Screws: Unscrew the heat sink from the motherboard.
• Lift the Heat Sink: Carefully detach it from the processor.
• Apply Thermal Paste: Clean old paste and apply new thermal paste on the CPU.
• Install the New Heat Sink: Position it back and secure it with screws.

Step 12: Replace the System Board

• Unscrew the System Board: Remove screws and disconnect cables connected to the board.
• Lift Out the Old Board: Carefully remove it from the chassis.
• Install the New System Board: Place the new board in, reconnect all cables, and secure with screws.

Step 13: Replace the Speakers

• Locate the Speakers: Usually found near the base enclosure.
• Unscrew and Disconnect: Remove screws and unplug the speaker cables.
• Install New Speakers: Place new speakers in position and reconnect cables.

Step 14: Replace the Smart Card Reader Board

• Find the Smart Card Reader: It is usually located near the front edge.
• Unscrew and Disconnect: Remove screws and unplug the connector.
• Install New Reader Board: Position the new board and reconnect.

Step 15: Change the Display Panel Assembly

• Remove the Top Cover: Unscrew and disengage the top cover from the base.
• Disconnect the Display Cable: Unplug the cable from the motherboard.
• Lift Off the Panel: Carefully remove the old display panel.
• Install the New Display Panel: Place the new panel and reconnect the display cable.

Conclusion

By following these step-by-step instructions, you can safely remove and replace various parts of the HP EliteBook x360 830 G8 Notebook PC. Always ensure you have the right tools and replacement parts before starting. For further assistance, consider visiting HP's support pages or forums. Happy upgrading!