How to Replace Rear Brakes 07-11 Honda CR-V

Introduction

This tutorial provides a step-by-step guide to replacing the rear brakes on a 2007-2011 Honda CR-V. Whether you're experiencing squeaky or fading brakes, this process can help you restore your vehicle's braking performance.

Step 1: Gather Your Tools

Before starting, make sure you have the following tools:

• Flat Blade Screwdriver
• Phillips Head Screwdriver
• 12mm Wrench
• 17mm Wrench
• 19mm Socket
• Brake Caliper Compressor Tool (screw style)
• Ratchet
• Socket Extensions
• Anti-Seize Grease
• Brake Parts Cleaner
• Bungee Cord
• Wire Brush

Step 2: Remove the Wheel

1. Use a 19mm socket and a breaker bar to loosen the lug nuts while the vehicle is on the ground.
2. Raise and support the vehicle securely using jack stands.
3. Remove the lug nuts completely and take off the wheel.

Step 3: Remove the Brake Caliper

1. Locate the two Phillips head screws on the brake caliper. Remove these using a Phillips head screwdriver or impact driver if needed.
2. Clean any rust around the caliper bolts with a wire brush for easier removal.
3. Use a 12mm socket and ratchet to loosen the caliper bolts. If the caliper pin spins, hold it in place with a 17mm wrench.
4. Gently twist the caliper to compress the piston and remove it from the bracket.

Step 4: Secure the Caliper

1. Use a bungee cord to hang the caliper securely, avoiding strain on the brake line.

Step 5: Remove Old Brake Pads and Caliper Bracket

1. Remove the old brake pads from the caliper.
2. Next, remove the two caliper bracket bolts using a 17mm socket and breaker bar.
3. Once loosened, take them out with a smaller ratchet and remove the bracket.

Step 6: Remove the Rotor

1. Pull the rotor straight off; if it's stuck, gently hammer it at specific points to loosen it.
2. Remove the plug from the rotor using a flat blade screwdriver.

Step 7: Install New Rotor

1. Clean the hub using a wire brush.
2. Install the new rotor, ensuring it is correctly aligned with the holes.
3. Spray the rotor with brake parts cleaner and wipe it down to remove any protective coating.

Step 8: Install the Caliper Bracket

1. Reinstall the caliper bracket and tighten the bolts securely.
2. Use a torque wrench to tighten the bolts to 79 foot-pounds.

Step 9: Prepare and Install New Brake Pads

1. Apply brake caliper grease to the ears of the new brake pads.
2. Install the new brake pads, ensuring they fit correctly into the caliper piston.

Step 10: Compress the Caliper Piston

1. Use an old brake pad and a brake caliper compressor tool to push the piston back into the caliper.
2. Ensure the piston is fully compressed, allowing room for the new pads.

Step 11: Reattach the Caliper

1. Remove the bungee cord and position the caliper over the new brake pads.
2. Install the caliper bolts and tighten them using a torque wrench to 17 foot-pounds.

Step 12: Reinstall the Wheel

1. Place the wheel back onto the hub and hand-tighten the lug nuts.
2. Lower the vehicle and use a torque wrench to tighten the lug nuts to 80 foot-pounds in a star pattern.

Step 13: Final Checks

1. Pump the brake pedal to remove any air gaps between the caliper piston and brake pads.
2. Ensure the brakes feel firm before taking the vehicle for a test drive.

Conclusion

Replacing the rear brakes on your Honda CR-V is a manageable task with the right tools and approach. By following these steps, you can save on labor costs and ensure your braking system is functioning optimally. For quality parts, consider visiting 1AAuto.com for your replacement needs. Happy driving!