PS5 Teardown (Disassembly Guide)

Introduction

This tutorial provides a comprehensive guide on how to disassemble a PlayStation 5 (PS5), specifically the disk edition. Whether you're looking to upgrade your storage, clean internal components, or perform repairs, following these steps will help you safely and effectively take apart your PS5.

Chapter 1: Stand Removal

1. Remove the Stand:
   • If the stand is attached, use a flathead screwdriver to remove the screw that secures it.
   • After removing the screw, carefully take off the stand.

Chapter 2: Case Removal

1. Remove the Top Cover:

   • Gently hit the top cover to release the clips and slide it off.

2. Remove the Bottom Cover:

   • Flip the console over and repeat the process to remove the bottom cover.

3. Access the Fan:

   • Locate the Torx T9H screws securing the fan in place using the appropriate bit from your toolkit.
   • Remove these screws.

Chapter 3: SSD Slot

1. Identify the SSD Slot:

   • This slot allows for an M.2 SSD upgrade. Remove the Phillips screw that holds the SSD bay cover to access it.

2. Remove the Cover:

   • Take off the SSD bay cover to reveal the slot.

3. Disconnect the Fan Cable:

   • Gently peel off the sticker covering the connectors.
   • Pinch the connector (not the yellow part) to release it.

Chapter 4: Fan Removal

1. Remove Fan Screws:

   • Use the T9H screwdriver to remove the four screws securing the fan.

2. Lift the Fan Out:

   • Carefully lift the fan out of the PS5.

Chapter 5: Removing the Warranty Sticker Without Voiding It

1. Heat the Sticker:

   • Use a heat gun or a hair dryer to warm the warranty sticker, which helps avoid damage during removal.

2. Peel Off the Sticker:

   • Slowly and carefully peel off the sticker once heated.

3. Remove the Screw:

   • With the sticker off, access and remove the Torx T9H screw underneath.

Chapter 6: Disc Drive

1. Disconnect the Ribbon Cable:

   • Push down on the retaining clip of the ribbon cable and pull it out gently.

2. Remove the Disc Drive:

   • Lift the Blu-ray disc drive out of the console.

3. Observe the Logic Board:

   • Note that this drive has a dedicated logic board, making it less repairable.

Chapter 7: Disassembling the Disc Drive

1. Remove Screws:

   • Use a Phillips screwdriver to remove screws securing the top of the disc drive.

2. Separate the Logic Board:

   • Carefully lift the logic board out of the disc drive, being cautious with the ribbon cables.

3. Inspect Internal Components:

   • Observe the laser deck and other components inside the drive.

Chapter 8: Midframe Removal

1. Disconnect Antenna Cables:

   • Carefully remove the antenna cables, noting their placement.

2. Remove Torx Screws:

   • Remove the Torx T9H screws that secure the midframe.

3. Lift the Plate:

   • Gently lift the midframe to access the motherboard.

Chapter 9: Heatsink and Motherboard

1. Remove Heatsink Screws:

   • Unscrew the screws holding the heatsink in place.

2. Lift the Heatsink:

   • Carefully lift the heatsink away from the motherboard.

3. Inspect the Motherboard:

   • Look for components like the APU, RAM, and any chips that may be prone to failure.

Chapter 10: Power Supply

1. Remove Power Supply Screws:

   • Use a larger Phillips screwdriver to unscrew the power supply.

2. Lift Out the Power Supply:

   • Carefully remove the power supply from the case.

Chapter 11: Antenna Removal

1. Disconnect the Antenna:
   • Push down on the connector and lift the antenna out.

Conclusion

You have successfully disassembled your PS5. This process allows for upgrades, repairs, and thorough cleaning of internal components. Always handle parts with care to avoid damage. If you have any further questions or need assistance, feel free to reach out. Enjoy your enhanced PS5 experience!